Partner P 352-16 35cc Russia User Manual download pdf (Page 7)

IMPORTANT

Experience indicates that alcohol blended fuels

(called gasohol or using ethanol or methanol)

can attract moisture which leads to separation

and formation of acids during storage. Acidic

gas can damage the fuel system of an engine

while in storage. To avoid engine problems,

empty the fuel system before storage for 30

days or longer . Drain the gas tank, start the en-

gine and let it run until the fuel lines and carbu-

retor are empty. Use fresh fuel next season.

Never use engine or carburetor cleaner prod-

ucts in the fuel tank or permanent damage may

occur.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling

the front hand guard back toward the front han-

dle as far as possible. The chain brake must

be disengaged before cutting with the saw.

WARNING: The chain must not

move when the engine runs at idle speed. If

the chain moves at idle speed refer to CAR-

BURETOR ADJUSTMENT within this

manual. Avoid contact with the muffler . A hot

muffler can cause serious burns.

To stop the engine, move the ON/STOP

switch to the STOP position.

To start the engine, hold the saw firmly on

the ground as illustrated below . Make sure

the chain is free to turn without contacting

any object.

Hold saw firmly while pulling starter rope.

Use only 15″ --- 1 8 ″ of rope per pull.

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full

extent of the rope as this can cause the rope to

break. Do not let starter rope snap back. Hold

the handle and let the rope rewind slowly.

For cold weather starting, start the unit at full

choke; allow the engine to warm up before

squeezing the throttle trigger.

NOTE: Do not cut material with the choke/fast

idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or a

warm engine after running out of

fuel)

NOTE

: In the following steps, when the cho-

ke/fast idle lever is pulled out to the full ex-

tent, the correct throttle setting for starting is

set automatically.

ON/STOP SWITC H

STOP

(SIDE VIEW)

1. Move ON/STOP switch to the ON posi-

tion.

2. Pull out choke/fast idle to the full extent

(to the FULL CHOKE position).

3. Slowly press primer bulb 6 times.

4. Pull the starter rope sharply 5 times with

your right hand. Then, proceed to the

next step.

NOTE: If the engine sounds as if it is trying

to start before the 5th pull, stop pulling and

immediately proceed to the next step.

5. Push the choke/fast idle lever in to the

HALF CHOKE position.

OFF HALF

CHOKE/FAST IDLE LEVER

Choke/

fast idle lever

(SIDE VIEW)

FULL

6. Pull the starter rope sharply with your

right hand until the engine starts.

7. Allow the engine to run for approximately

5 seconds. Then, squeeze and release

throttle trigger to allow engine to return to

idle speed.

STARTING A WARM ENGINE

1. Move ON/STOP switch to the ON posi-

tion.

2. Pull the choke/fast idle lever out to the

HALF CHOKE position.

3. Slowly press the primer bulb 6 times.

4. Pull the starter rope sharply with your

right hand until the engine starts.

5. Squeeze and release throttle trigger to

allow engine to return to idle speed.

DIFFICULT STARTING (or starting a

flooded engine)

The engine may be flooded with too much

fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess

fuel by pushing the choke/fast idle lever in

completely (to the OFF CHOKE position)

and then following the warm engine starting

procedure listed above. Ensure the ON/

STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

the unit is flooded. If engine fails to start, re-

fer to the TROUBLESHOOTING TABLE.

CHAIN BRAKE

WARNING: If the brake band is worn

too thin it may break when the chain brake is

triggered. With a broken brake band, the

chain brake will not stop the chain. The chain

brake should be replaced by an authorized

service dealer if any part is worn to less than

0,02″ (0,5 mm) thick. Repairs on a chain

brake should be made by an authorized ser-

vice dealer. Take your unit to the place of pur-

chase if purchased from a servicing dealer ,

or to the nearest authorized master service

dealer.

S This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Partner P 352-16 35cc Russia User Manual Page 7

Comments to this Manuals